FUJI FC Series CCS communication driver

FUJI FC Series CCS communication driver is the driver to communicate with CCS controller of Fuji Electric Co., Ltd. in Japan.

1. Read settings

<Figure 1> is read setting example of FUJI FC Series CCS communication driver. 

<Figure 1>  Read setting example of  FUJI FC Series CCS communication driver

Device part of  <Figure 1> input Com Port(COM1), Baud Rate(19200), Parity Bit(1), Data Bit(8), Stop Bit(1) respectively according to setting of controller.

Note) Baud rate, Parity bit, Data bit, Stop bit are set by using controller's 'setting switch' of front panel.

Default Baud rate,  Parity bit, Data bit, Stop bit are 19200 BPS, 1 Parity, 8 Data Bit, 1 Stop Bit.

FUJI FC Series CCS communication driver read schedule

Read schedule setting parameters are as follows:

1) STATION – CCS station number = 1 ~ 31.

2) Read file number – File number = 0 ~ 127. (  Refer to <Table 1> )

3) Read start address – Read start address in each file = 0 ~ 255(varies address according to file area).

4) Save Start Address for Communication Server – saveing start address of Communication Server.

5) Read Size – Read size of Word unit = 1 ~ 16.

Read schedule example)

READ,     1,     0,     0,    0,   5,

READ,     1,     1,     0,    5,   9,

READ,     1,     2,     0,   15,  16,

<Table 1> is file number and contents of FUJI FC Series CCS communication driver.

Please refer to Instruction Manual of FUJI FC Series CCS Controller for more data contents and address in each file.

If you click the icon  in protocol option part, you can see the dialogue box such as <Figure 2>. you can also set read schedule by using this part.

<Figure 2> Example of   FUJI FC Series CCS communication driver’s Option dialogue box

You can set read schedule by using , , button and listbox of <Figure 2>. 

<Figure 3> Example of   FUJI FC Series CCS communication driver’s read schedule Add/Edit dialogue box

When you click Add button or Edit button in dialogue box of <Figure 2>, dialogue box of <Figure 3> is shown.

2. Write settings

You can set the file value by using write settings.

Digital Write

Digital write setting parameters are as follows:

1)  PORT                   Port no. (0 ~ 255)

2)  STATION             CCS station number = 1 ~ 31.

3)  ADDRESS          Write address in each file = 0 ~ 255(varies address according to file area).

Higher 3 digit : 0 ~ 255 word address,

Lower 1 digit : 0 ~ F bit address.

4) Extra1                   Write file number = 0 ~ 127 only writable area. ( Refer to <Table 1>)

5) Extra2                   Contents of output.

1 : Output of control, in this case Address, Extra1 = don't care,

0, space, etc : Normal output setting.

Write example 1)

PORT:0,  station:1, ADDRESS:0113, Extra1: 4,  Extra2 :

The setting parameter shown above is a bit write(On/Off) example of  3(4th) bit, 11(12th) word in 4 file number.

Analog Write

Analog write setting parameters are as follows:

1)  PORT                   Port no. (0 ~ 255)

2)  STATION             CCS station number = 1 ~ 31.

3)  ADDRESS           Write address in each file = 0 ~ 255(varies address according to file area).

4) Extra1                    Write file number = 0 ~ 127 only writable area. ( Refer to <Table 1>)

5) Extra2                   Contents of output.

1 : Output of control, in this case Address, Extra1 = don't care,

0, space, etc : Normal output setting.

Write example 1)

PORT:0,  station:1, ADDRESS:0009, Extra1: 4,  Extra2 :

The setting parameter shown above is analog write example of  9(10th : P value) word in 4 file number(Main block parameter file).

Write example 2)

PORT:0,  station:1, ADDRESS:0010, Extra1: 4,  Extra2 :

The setting parameter shown above is analog write example of  10(11th : I value) word in 4 file number(Main block parameter file).

3. connection of communication cable, main power and setting baud rate

Connection of communication cable, main power and setting baud rate are as follows.

Connection of communication cable

Please connect RS-422/485 communication cable to 4(Tx+), 5(Tx-), 8(Rx+), 9(Tx-) connector of FUJI FC Series CCS Controller such as <Figure 4>. ( usable both 9pin connector )

Computer side            FUJI FC Series CCS Controller side

Tx+  --------------------------------- Rx+

Tx-  --------------------------------- Rx-

Rx+  --------------------------------- Tx+

Rx-  --------------------------------- Tx-

<Figure 4> Connection example of  communication cable and main power to FUJI FC Series CCS

Connection of main power

Please connect 110V AC to 16(AC), 35(AC) such as <Figure 4>.

<Figure 5> is appearence of FUJI FC Series CCS Controller.

<Figure 5> Appearence of FUJI FC Series CCS Controller

Setting of baud rate, data, parity, stop bit

You can set baud rate, data, parity, stop bit by using front panel's 'setting button' of FUJI FC Series CCS Controller. ( Refer to Instruction Manual of FUJI FC Series CCS )